Solar Cell Peeling Tester Ribbon Puller PV Module Procuction Line Tester

• After-sales Service: 24 Hours Online
• Warranty: 1 Year
• Max Diameter of Workpiece: <500mm
• Model NO.: HT-9100S-1
• Mass Scope of Workpiece: <900kg
• Type: Testing Machine
• Maxcapacity: <1000KN
• Accuracy Grade: 1
• Load Way: Mechanical Load
• Loading Method: Dynamic Load
• Display: Digital
• Control: Manual Control
• Weight: 500-1000Kg
• Power Source: AC220V
• Oil Cylinder Position: None
• Transport Package: Wooden Case
• Specification: 1250 * 580 * 1230mm
• Trademark: HOTOTECH
• Origin: China
• Package Size: 125.00cm * 58.00cm * 123.00cm

Product Description

Product Description

Purpose:
Mainly used to test the welding strength between the main grid line of the Solar cell and the interconnection solder strip.
Technical specification:

Optional maximum test force	within 20N
Accuracy level of testing machine	0.5 level
Test force measurement range	0.1% -100% FS
Relative error of test force indication	Within ± 0.5% of the indication
Experimental resolution	1/± 500000 of the maximum experimental force (with constant resolution throughout the entire process)
Relative error of displacement indication	within ± 0.5% of the indication
Displacement resolution	0.001mm
Range of force control rate adjustment	0.1-5% FS/S
Relative error of force control rate	within ± 1% of the set value
Relative error of force control rate	within ± 1% of the set value
Beam speed adjustment range	0.05-1000mm/min
Constant force, constant deformation, constant displacement control range	0.5% -100% FS
Constant force, constant deformation, and constant displacement control accuracy	When the set value is less than 10% FS, it is within ± 1% of the set value; When the set value is ≥ 10% FS, it is within ± 0.1% of the set value
Maximum stretching stroke	450mm
Effective test width	300mm
Host dimensions (length x width x height)	approximately 1250 * 580 * 1230mm
Power supply	220V 50Hz 400W
Host weight	approximately 150kg
The tension angle should be 180 ± 2 degrees
Control methods such as fixed speed, positioning displacement, and fixed load can be selected
Meet the tensile verification requirements for single and double-sided 5BB-15BB batteries with sizes of 156.75, 158.75, 166, 182, 210, 230, etc
Independently disassemble and adjust sensor and fixture components, capable of testing at workstations 5, 6, 9, 10, 11, 12, and 15
The control program has high sensitivity and meets the continuity of high-frequency use
Configure Lenovo dedicated computer
Test software in both Chinese and English
The machine is equipped with a standard aluminum alloy frame, and tools or samples can be placed in the cabinet below.

Introduction to Software Testing Functions
1. Load displacement curve; Load and time curves; Displacement and time curves; Stress and strain curves.
2. According to the requirements of each country for test specimens, edit corresponding testing standards, fill in sample information, edit testing methods, and provide options for future testing.
3. Automatically store the results of this experiment and edit them into a report for printing and output. There is a formula editing function that allows for comparison of multiple tested curves.
4. Can set decimal places, physical units, and password protection.
5. Auto reset: When the computer receives the instruction to start the experiment, the measurement system automatically resets to zero;
6. Automatic regression: Automatically identify the maximum force of the experiment, and the movable crossbeam automatically returns to its initial position at high speed;
7. Automatic archiving: Test data and conditions are automatically saved to prevent data loss caused by forgetting to save due to sudden power outages;
8. Testing process: The testing process, measurement, display, analysis, etc. are all completed by a microcomputer;
9. Display mode: Data and curves are dynamically displayed during the experimental process;
10. Structural reproduction: The experimental results can be accessed freely and the data curve can be reanalyzed;
11. Curve traversal: After the experiment is completed, the mouse can be used to find the force values and deformation data of the test curve point by point, which is convenient and practical for obtaining test data of various materials;
12. Result comparison: Multiple experimental characteristic curves can be overlaid, reproduced, enlarged, and presented in different colors to analyze and compare a group of samples;
13. Curve selection: Stress strain, force time, strength time and other curves can be selected as needed for display and printing;
14. Batch experiment: After setting the same parameters for one experiment, a batch of samples can be tested sequentially;
15. Test report: standard format;
16. Limit protection: It has two levels of protection: programmable control and mechanical protection;
17. Overload protection: automatic shutdown when the load exceeds 10% of the rated value;
18. Emergency stop: equipped with an emergency stop switch, used to cut off the power supply of the entire machine in emergency situations;
19. Automatic diagnosis: The system has an automatic diagnosis function, which checks the measurement system and drive system for overvoltage, overcurrent, overtemperature, etc. at regular intervals. If any abnormal situation occurs, the machine will be stopped immediately.

Company Profile